Intel B940 Datasheet Page 322
- Page / 360
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Processor Configuration Registers
322 Datasheet, Volume 2
2.19.42 SLOTCTL—Slot Control Register
Note: Hot Plug is not supported on the platforms.
B/D/F/Type: 0/6/0/PCI
Address Offset: B8–B9h
Reset Value: 0000h
Access: RO, RW
Bit Attr
Reset
Value
Description
15:13 RO 000b Reserved
12 RO 0b
Reserved for Data Link Layer State Changed Enable (DLLSCE)
If the Data Link Layer Link Active capability is implemented, when set to 1b,
this field enables software notification when Data Link Layer Link Active field
is changed.
If the Data Link Layer Link Active capability is not implemented, this bit is
permitted to be read-only with a value of 0b.
11 RO 0b
Reserved for Electromechanical Interlock Control (EIC)
If an Electromechanical Interlock is implemented, a write of 1b to this field
causes the state of the interlock to toggle. A write of 0b to this field has no
effect. A read to this register always returns a 0.
10 RO 0b
Reserved for Power Controller Control (PCC)
If a Power Controller is implemented, this field when written sets the power
state of the slot per the defined encodings. Reads of this field must reflect
the value from the latest write, even if the corresponding hotplug command
is not complete, unless software issues a write without waiting for the
previous command to complete in which case the read value is undefined.
Depending on the form factor, the power is turned on/off either to the slot or
within the adapter. Note that in some cases the power controller may
autonomously remove slot power or not respond to a power-up request
based on a detected fault condition, independent of the Power Controller
Control setting.
The defined encodings are:
0b = Power On
1b = Power Off
If the Power Controller Implemented field in the Slot Capabilities register is
set to 0b, then writes to this field have no effect and the read value of this
field is undefined.
9:8 RO 00b
Reserved Power Indicator Control (PIC)
If a Power Indicator is implemented, writes to this field set the Power
Indicator to the written state. Reads of this field must reflect the value from
the latest write, even if the corresponding hot-plug command is not
complete, unless software issues a write without waiting for the previous
command to complete in which case the read value is undefined.
00 = Reserved
01 = On
10 = Blink
11 = Off
If the Power Indicator Present bit in the Slot Capabilities register is 0b, this
field is permitted to be read-only with a value of 00b.
- Datasheet – Volume 2 1
- Legal Lines and Disclaimers 2
- Contents 3
- 4 Datasheet, Volume 2 4
- Datasheet, Volume 2 5 5
- 6 Datasheet, Volume 2 6
- Datasheet, Volume 2 7 7
- 8 Datasheet, Volume 2 8
- Datasheet, Volume 2 9 9
- 10 Datasheet, Volume 2 10
- Datasheet, Volume 2 11 11
- Revision History 12
- 1 Introduction 13
- Introduction 14
- 2 Processor Configuration 15
- 2.2 System Address Map 17
- 18 Datasheet, Volume 2 18
- 2.2.1 Legacy Address Range 19
- Datasheet, Volume 2 21 21
- 2.2.2.2 TSEG 22
- 2.2.2.5 Pre-allocated Memory 23
- 2.2.2.7 Intel 24
- Management Engine (Intel 24
- ME) UMA 24
- Datasheet, Volume 2 25 25
- 2.2.2.10 High BIOS Area 26
- Datasheet, Volume 2 27 27
- 2.2.3.1 Programming Model 28
- HOST/SYSTEM VIEW 29
- PHYSICAL MEMORY 29
- (DRAM CONTROLLER VIEW) 29
- Datasheet, Volume 2 33 33
- 34 Datasheet, Volume 2 34
- 2.2.9 I/O Address Space 35
- 36 Datasheet, Volume 2 36
- Datasheet, Volume 2 37 37
- 2.4 Configuration Mechanisms 38
- Datasheet, Volume 2 39 39
- 40 Datasheet, Volume 2 40
- Datasheet, Volume 2 41 41
- 42 Datasheet, Volume 2 42
- Datasheet, Volume 2 43 43
- 2.6 I/O Mapped Registers 44
- 2.7.6 CC—Class Code Register 49
- TXT Lockable 54
- 1:0 to 11b 56
- 4) from 58
- B0h, bits 15:4) 58
- 2.8 MCHBAR Registers 66
- 00h RW 67
- Register Symbol Register Name 67
- 208–209h 73
- 20A–20Bh 74
- 24D–24Fh 74
- 250-251h 75
- 252–255h 76
- 256–257h 77
- 258–25Ah 77
- 269–26Eh 79
- 298–29Bh 82
- 29C–29Fh 84
- 2B4–2B7h 84
- 600–601h 86
- 602–603h 86
- 604–605h 86
- 64D–64Fh 88
- 650–651h 88
- 652–655h 89
- 656–657h 90
- 658–65Ah 90
- 660–663h 91
- 6B4–6B7h 93
- C20–C27h 94
- 1001–1002h 94
- 1004–1005h 95
- 101E–101Fh 100
- Register 107
- 10EC–10EDh 108
- 2C20–2C22h 109
- 2.9 EPBAR Registers 110
- 2.10 PCI Device 1 Registers 115
- PCI device 117
- Port Command Register 140
- 11:10 RW-O 11b 143
- OS's during run time 155
- 104–107h 156
- 108–10Bh 157
- 10C–10Dh 157
- 110–113h 158
- 23 RO 0b Reserved 158
- 114–117h 158
- 11A–11Bh 159
- 2.12 DMIBAR Registers 161
- Declaration Capability 169
- 2.13.6 CC—Class Code Register 177
- Range Address Register 179
- GMADR register 180
- 2.14 Device 2 I/O Registers 183
- 100–107h 211
- 108–10Fh 212
- 200–20Fh 214
- F00–F03h 215
- F04–F07h 216
- Dedication 217
- F08–F0Bh 218
- FFC–FFFh 219
- 2.16 DMI VC1 REMAP Registers 221
- 2.17.2 GFXPLL1—GFX PLL BIOS 254
- 2.18 GFXVTBAR Registers 255
- Address Register 281
- 2.19 PCI Device 6 Registers 288
- 2.19.45 RSTS—Root Status 327
- 2.21 Intel 332
- Specific Registers 332
- 110–117h 333
- 330–337h 333
- Lower Half Register 334
- Upper Half Register 334
- QuickPath Architecture 335
- System Address Decode 335
- Register Description 335
- QPI Link 0 Registers 340
- QPI Physical 0 Registers 341
- 3.4 PCI Standard Registers 342
- 3.4.4 CCR—Class Code Register 344
- Identification Register 345
- 3.4.7 PCICMD—Command Register 346
- 3.5.1 MAX_RTIDS 349
- 3.6.1 SAD_PAM0123 349
- 3.6.2 SAD_PAM456 351
- 3.6.3 SAD_HEN 352
- 3.6.4 SAD_SMRAM 353
- 3.6.5 SAD_PCIEXBAR 354
- 3.7 Intel 356
- QPI Link Registers 356
- 3.8 Intel 357
- QPI Physical Layer Registers 357
- 360 Datasheet, Volume 2 360
Related products and manuals for Processors Intel B940
Processors Intel core 2 Duo T5850 Specifications
(292 pages)
(292 pages)
Processors Intel AT80569KJ073N Datasheet
(102 pages)
(102 pages)
© 2020, manymanuals.com. All rights reserved. | 0.468 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals