Intel S1200BTSR Datasheet Page 125
- Page / 153
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Intel® Server Board S1200BT TPS Design and Environmental Specifications
Revision 1.0
Intel order number G13326-003
113
10.3.1 Grounding
The grounds of the power supply output connector pins provide the power return path. The
output connector ground pins are connected to the safety ground (power supply enclosure).
This grounding is designed to ensure passing the maximum allowed common mode
noise levels.
The power supply is provided with a reliable protective earth ground. All secondary circuits are
connected to protective earth ground. Resistance of the ground returns to chassis does not
exceed 1.0 m. This path may be used to carry DC current.
10.3.2 Standby Outputs
The 5 VSB output is present when an AC input greater than the power supply turn on voltage
is applied.
10.3.3 Remote Sense
The power supply has remote sense return (ReturnS) to regulate out ground drops for all output
voltages: +3.3 V, +5 V, +12 V, -12 V, and 5 VSB. The power supply uses remote sense to
regulate out drops in the system for the +3.3 V, +5 V, and 12 V outputs. The power supply must
operate within specification over the full range of voltage drops from the power supply‘s output
connector to the remote sense points.
10.3.4 Voltage Regulation
The power supply output voltages must stay within the following voltage limits when operating
at steady state and dynamic loading conditions. These limits include the peak-peak ripple/noise.
All outputs are measured with reference to the return remote sense signal (ReturnS).
Table 48. Voltage Regulation Limits
Parameter
Tolerance
Minimum
Normal
Maximum
Units
+ 3.3 V
- 5% / +5%
+3.14
+3.30
+3.46
Vrms
+ 5 V
- 5% / +5%
+4.75
+5.00
+5.25
Vrms
+ 12 V
- 5% / +5%
+11.40
+12.00
+12.60
Vrms
- 12 V
- 10% / +10%
-13.20
-12.00
-10.80
Vrms
+ 5 VSB
- 5% / +5%
+4.75
+5.00
+5.25
Vrms
10.3.5 Dynamic Loading
The output voltages remain within limits for the step loading and capacitive loading specified in
the following table. The load transient repetition rate is tested between 50 Hz and 5 kHz at duty
cycles ranging from 10%-90%. The load transient repetition rate is only a test specification. The
step load may occur anywhere within the Min load to the Max load conditions.
Table 49. Transient Load Requirements
Output
∆ Step Load Size
(See note 2)
Load Slew Rate
Test capacitive Load
+3.3 V
5.0 A
0.25 A/µsec
250 µF
+5 V
6.0 A
0.25 A/µsec
400 µF
12 V
11.0 A
0.25 A/µsec
500 µF
- Server Board S1200BT 1
- Revision History 2
- Disclaimers 3
- Table of Contents 4
- List of Figures 8
- List of Tables 10
- Revision 1.0 11
- 1. Introduction 13
- 2. Overview 14
- 2.2 Server Board Layout 16
- 2.2.2 Intel 20
- 3. Functional Architecture 27
- 3.1 Processor Sub-System 28
- 3.2 Memory Subsystem 29
- 3.2.1 Memory Supported 30
- 3.2.2 Post Error Codes 30
- 3.3 Intel 33
- Chipset PCH 33
- 3.4 I/O Sub-system 34
- 3.4.5 USB 2.0 Support 35
- 3.5 Optional Intel 36
- SAS RAID Module 36
- 3.6.3 Serial Ports 39
- 3.7 Video Support 40
- 3.7.2 Video for Intel 41
- Server Board S1200BTS 41
- 4. Platform Management 44
- 4.1 Feature Support 45
- 4.2.3 Media Redirection 50
- 4.2.4 Embedded Web server 51
- 4.3 Thermal Control 53
- 4.4 Intel 54
- 4.4.2 Features 55
- Server 58
- Board S1200BTS 58
- 6. BIOS User Interface 59
- 6.4 BIOS Boot Pop-up Menu 62
- 6.5 BIOS Setup Utility 62
- Table 16. Screen Map 66
- Frequency 74
- Hardware Prefetcher 74
- Adjacent Cache Line Prefetch 74
- 6.5.2.8 USB Configuration 84
- [40%/60%/80%/100%] 93
- Revision 1.0 102
- 7.2 Power Connectors 103
- 7.3.1 Intel 104
- RMM4) Lite connetor and 104
- Dedicated NIC connector 104
- 7.3.4 SGPIO Header 105
- 7.3.2 LPC/IPMB Header 105
- 7.3.3 HSBP Header 105
- 7.4.1 Power Button 106
- 7.4.2 Reset Button 107
- 7.5 I/O Connectors 108
- 7.5.3 SATA 109
- 7.5.4 SAS Connectors 109
- 7.5.6 USB Connector 111
- 7.7 Fan Headers 115
- 8. Jumper Blocks 116
- 8.1.1 Clearing the CMOS 118
- 8.1.2 Clearing the Password 118
- Server Board S1200BTL) 119
- 8.3 ME Force Update Jumper 119
- 8.4 BIOS Recovery Jumper 120
- 9. Intel 121
- Light Guided Diagnostics 121
- 10.1 Intel 123
- 10.3.1 Grounding 125
- 10.3.2 Standby Outputs 125
- 10.3.3 Remote Sense 125
- 10.3.4 Voltage Regulation 125
- 10.3.5 Dynamic Loading 125
- 10.3.6 Capacitive Loading 126
- 10.3.8 Common Mode Noise 126
- 10.3.9 Ripple/Noise 126
- 10.3.10 Timing Requirements 126
- 10.3.12 Protection Circuits 129
- Sensor Type Codes 132
- Table 56. BMC Core Sensors 134
- Appendix D: POST Code Errors 145
- POST Error Beep Codes 147
- Appendix E: Supported Intel 148
- Server Chassis 148
- Glossary 149
- Reference Documents 153
Comments to this Manuals
Related products and manuals for Server/workstation motherboards Intel S1200BTSR
(4 pages)
(1 pages)© 2020, manymanuals.com. All rights reserved. | 1.472 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Hello, im noob :)