Intel IP-4GVI63 User Manual

IP-4GVI63 Series (Industrial Board) INSTALLATION GUIDE Installation Guide Revision A2 6007002463A20

Introduction 4 ¡ IO Connectivity - ICH4: - 6 Hi-Speed USB2.0 ports - 10/100 Base-TX Ethernet 1.3.2 Ultra ATA/66/100 The ICH4 provides two chan

Introduction 5 1.3.5 Power-On/Off (Remote) The board has a single 20-pins connector for ATX power supplies. For ATX power supplies that support th

Introduction 6 1.3.7 System Block Diagram P4 Socket 478-pinsClockVRMDATACTRLADDRGMCH (845GV)760 FC-BGAICH4421 BGADDR266/333 X2CRTDeviceSuper I/OW

Introduction 7 1.4 Specifications ¡ Processor: - Intel® Pentium® 4/Celeron™ processor with socket 478-pins package, Processor operating at 1.3GH

Introduction 8 ¡ Onboard PCI / IDE: - Intel® 82801DB (ICH4) controller - PCI rev2.2 Compliant - ACPI Compliant Power Management - PCI bus

9 INSTALLATIONS 2.1 System Installation 2.1.1 CPU Installation Carefully follow the steps below in order to install the CPU: 1. Check and con

Installations 10 Removing a CPU: 1. Before removing the CPU, turn off the IP-4GVI63 Series power; then wait for about 20 minutes until the heat radi

Installations 11 2.1.3 Memory Module Installation Figure 5 display the notch marks and what they should look like on your DIMM memory module. DIM

Installations 12 Carefully follow the steps below in order to install the DIMMs: 1. To avoid generating static electricity and damaging the DIMM, gr

Installations 13 2.1.4 Setting Jumpers There are jumpers on the system board of the IP-4GVI63 Series. You can set the jumpers to make the necessar

Installations 14 2.2 Board Layout Jumper & Connector Location ATX2FAN1DIMM2DIMM1POWER FANJP3IP-4GVI63JBAT1IDE1IDE2J2J1FAN3FAN4J3FDD1CHASSIS F

Installations 15 2.3 Jumper Setting Table for Jumper Location Description: Use the information in the following table to change the jumpers. Jumper

Installations 16 In order to set up the correct configuration, here is the description about how to set the jumpers to enable/disable or change funct

Installations 17  COM3 port setting select: JPB1 JPB1 Function 1-2 3-4 5-6 7-8 9-10 11-12 RS-232 (Default) Off Off Off Off Off On RS-422 On (Term.)

Installations 18 2.4 Connector’s Description Connector Location ATX2FAN1DIMM2DIMM1POWER FANJP3IP-4GVI63JBAT1IDE1IDE2J2J1FAN3FAN4J3FDD1CHASSIS FANBA

Installations 19 Table for Connector’s Location Description: Use the information in the following table to change the connector. Connectors Functio

Installations 20  Primary IDE connector (40-pins 2.54mm pitch pin-header with housing): IDE1 Pin # Assignment Pin # Assignment 1 Reset IDE 2 G

Installations 21  Secondary IDE connector (40-pins 2.54mm pitch pin-header with housing): IDE2 Pin # Assignment Pin # Assignment 1 Reset IDE 2

Installations 22  Floppy disk connector (34-pins 2.54mm pitch pin-header with housing): FDD1 Pin # Assignment Pin # Assignment 1 Ground 2 Drive

Installations 23  PS/2 keyboard connector (6-pins purple Mini Din): KBMS1 Pin # Assignment Pin # Assignment 1 Keyboard data 2 NC 3 Ground 4 +5V 5

i COPYRIGHT© All rights reserved. The information contained in this guide has been validated and reviewed for accuracy. No patent liability is assu

Installations 24  COM1 RS-232 serial port connector (D-Sub 9-pins male): COM1 Pin # Assignment Pin # Assignment 1 DCD (Data Carrier Detect) 6 D

Installations 25  CRT VGA port connector (D-SUB 15-pins female): VGA1 Pin # Assignment Pin # Assignment 1 Red 2 Green 3 Blue 4 NC 5 Ground 6 Grou

Installations 26  USB 3/4 connectors (4-pins female): USB2 Pin # Assignment Pin # Assignment 1a VCC 1b VCC 2a USB3 - 2b USB4 - 3a USB3 + 3b

Installations 27  Audio port connector: CN1 Pin # Assignment Blue Line-In Green Line-Out Red Mic-In y Figure:  CD_IN connector: CDIN1

Installations 28  AUX_IN connector: AUXIN1 Pin # Assignment 1 Left Line_IN 2 Ground 3 Ground 4 Right Line_IN_ y Figure:  Wake On LAN c

Installations 29  COM2 RS-232 serial port connector (10-pins pin-header): COM2 Pin # Assignment Pin # Assignment 1 DCD (Data Carrier Detect) 2

Installations 30  COM4 RS-232/422/485 serial port connector (14-pins pin-header): JCN2 Pin # Assignment Pin # Assignment 1 DCD (Data Carrier De

Installations 31  USB 5/6 pin-header (9-pins pin-header): USB3 Pin # Assignment Pin # Assignment 1 VCC 2 VCC 3 USB5 - 4 USB6 - 5 USB5 + 6 U

Installations 32  CPU fan power connector: FAN2 Pin # Assignment 1 Ground 2 +12V 3 Sense y Figure:  Chassis fan power connector: FAN3 P

Installations 33  ATX 12V power connector: ATX1 Pin # Assignment Pin # Assignment 1 Ground 2 Ground 3 +12V 4 +12V y Figure:  ATX power

ii CONTENTS SECTION 1 INTRODUCTION 1 1.1 Unpacking IP-4GVI63 Series 1 1.2 Description 3 1.3 Features 3 1.3.1 Graphic & Ethernet 3

Installations 34  System panel indicate connector: J1 & J2 Pin # J1 Assignment Pin # J2 Assignment PWR ON KEYLOCK 1 PWRBT- 1 Ground 2 5VSB 2

Installations 35  Slim floppy disk connector (26-pins FPC connector): J3 Pin # Assignment Pin # Assignment 1 +5V 14 Step 2 Index 15 Ground 3 +5V

36 AWARD BIOS SETUP 3.1 BIOS Instructions Award’s ROM BIOS provides a built-in Setup program, which allows user to modify the basic system confi

Award BIOS Setup 37 3.2 Main Menu Once you enter the AwardBIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows y

Award BIOS Setup 38 Integrated Peripherals: Use this menu to specify your settings for integrated peripherals. See section 4 for the details. Power

Award BIOS Setup 39 3.3 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, on

Award BIOS Setup 40 IDE Secondary Master: Options are in its sub menu (described in 3.4) Press <Enter> to enter the sub menu of detailed option

Award BIOS Setup 41 3.4 IDE Adapters The IDE adapters control the hard disk drive. Use a separate sub menu to configure each hard disk drive. Phoen

Award BIOS Setup 42 The following options are selectable only if the ‘IDE Primary Master’ item is set to “Manual” Cylinder: Options Min = 0, Max = 6

Award BIOS Setup 43 3.5 Advanced BIOS Features This section allows you to configure your system for basic operation. You have the opportunity to s

iii CONTENTS SECTION 3 AWARD BIOS SETUP 36 3.1 BIOS Instructions 36 3.2 Main Menu 37 3.3 Standard CMOS Features 39 3.4 IDE Adapters 41

Award BIOS Setup 44 Quick Power On Self Test: This category speeds up Power On Self Test (POST) after you power up the computer. If it is set to Ena

Award BIOS Setup 45 Swap Floppy Drive: If the system has two floppy drives, you can swap the logical drive name assignments. The choice: Enabled,

Award BIOS Setup 46 Security Option: Select whether the password is required every time the system boots or only when you enter setup. System---The

Award BIOS Setup 47 3.6 Advanced Chipset Features This section allows you to configure the system based on the specific features of the installed c

Award BIOS Setup 48 CAS Latency Time: When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. The

Award BIOS Setup 49 Delayed Transaction: The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select “Enable

Award BIOS Setup 50 3.7 Integrated Peripherals Phoenix - AwardBIOS CMOS Setup Utility Integrated Peripherals ¾ Onboard IDE Device Setup ¾ Onboard P

Award BIOS Setup 51 IDE Primary/Secondary Master/Slave PIO: The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each o

Award BIOS Setup 52 USB Keyboard Support: Select “Enabled” if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboar

Award BIOS Setup 53 Hot Key Power ON: You can use this item to select operating Hot Key to Power On system. The choice: Ctrl-F1 Onboard FDC Contro

iv

Award BIOS Setup 54 Parallel Port Mode: Select an operating mode for the onboard parallel (printer) port. Select Normal, Compatible, or SPP unless y

Award BIOS Setup 55 3.8 Power Management Setup The Power Management Setup allows you to configure you system to most effectively save energy while

Award BIOS Setup 56 Min. Power Saving: Minimum power management. Doze Mode = 1 hr. Standby Mode = 1 hr., Suspend Mode = 1 hr., and HDD Power Down =

Award BIOS Setup 57 Suspend Mode: When “Enabled” and after the set time of system inactivity. All devices except the CPU will be shut off. The cho

Award BIOS Setup 58 Reload Global Timer Events: The events are I/O events whose occurrence can prevent the system from entering a power saving mode o

Award BIOS Setup 59 3.9 PnP/PCI Configurations This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a s

Award BIOS Setup 60 3.10 PC Health Status Phoenix - AwardBIOS CMOS Setup Utility PC Health Status CPU Warning Temperature Current CPU Temp. Curre

Award BIOS Setup 61 Vagp (V) The voltage level of Power supplied to AGP card. Vcore (V) The voltage level of CPU (Vcore). Vdimm (V) The voltage lev

Award BIOS Setup 62 3.11 Frequency/Voltage Control Phoenix - AwardBIOS CMOS Setup Utility Frequency/Voltage Control CPU Clock Ratio Watch Dog Funct

Award BIOS Setup 63 Clock Generation for EMI: Clock Generation for EMI Auto Detect PCI Clk Spread Spectrum Modulated Enabled Disabled Item He

1 INTRODUCTION 1.1 Unpacking IP-4GVI63 Series 1. Take out the IP-4GVI63 series unit from the carton box, check if the unit is properly secure in

Award BIOS Setup 64 3.12 Load Fail-Safe Defaults When you press <Enter> on this item you get a confirmation dialog box with a message similar

Award BIOS Setup 65 3.14 Supervisor/User Password Setting You can set either supervisor or user password, or both of then. The differences between

Award BIOS Setup 66 3.15 Exit Selecting Save & Exit Setup Pressing <Enter> on this item asks for confirmation: Save to CMOS and EXIT (Y/N

Introduction 2 ¡ COM3 ribbon cable (1 Set) ¡ I/O Shield (for RS-232/422/485) 3. Optional Cable ¡ USB2.0 cable (optional) ¡ COM4 ribb

Introduction 3 1.2 Description The IP-4GVI63 Series combines the high performance and exceptional value of Intel® 845GV chipset with a full-featured